Taps, toilets and baths
Leaking tap repair and tap replacement
£50 to £150 is the typical price to repair a dripping tap, and £80 to £250 to supply and fit a replacement. Swapping a tap like for like is a common handyman job. Fitting a tap on extra pipework is plumbing work that a plumber may need to do.
Post your handyman job to Premium membersTell us about your job once. Premium handymen who cover your area can then contact you.Describe your job

What this covers
What it costs. Most dripping tap repairs cost £50 to £150 outside London, and £60 to £180 in London and the South East. Full cost breakdown.
What the job covers
- Fixing dripping and leaking taps
- Replacing washers and cartridges
- Swapping a kitchen tap
- Fitting bathroom and basin taps
- Replacing a bath tap
What is involved
A dripping tap usually needs a small part: a rubber washer in an older tap, or a ceramic cartridge in a modern mixer. A handyman turns off the water, takes the tap apart, replaces the worn part and puts it back, then checks for leaks. A tap that keeps dripping, has a stiff handle or shows corrosion and limescale damage may be better replaced than repaired.
Swapping a tap like for like, on the same pipes, is straightforward for many handymen. Published guides put a washer or seal repair at £50 to £70 outside London, a cartridge at £60 to £110 and a more complex valve repair at £90 to £140. Labour for a like-for-like replacement is £60 to £130 outside London, and supply and fit is £80 to £250 in total. The tap itself costs £30 to £100 for a pillar, £40 to £100 for a mixer, and more for wall-mounted and sensor taps.
The price depends on the type of tap and what is behind it. Pillar, mixer and monobloc taps are simple swaps, while bridge, wall-mounted and sensor taps take longer. If the existing pipes or isolation valves are worn or missing, extra work is needed, and fitting a tap where there was none means extra pipework. That is a plumbing job, so a plumber is the right person for it. Prices are often higher in London and the South East.
Before the visit, find your stopcock and any isolation valves under the sink, and check that they turn. Keep the tap model number or the box. If the tap is dripping, tell the handyman whether it is the hot or cold side. Never use a handyman for gas work: gas appliances and pipes need a Gas Safe registered engineer.

Fixing dripping and leaking taps, one of the jobs a handyman is hired for.
Choosing someone for the job
Ask whether the price covers the part or the tap as well as the labour. Ask whether the handyman does like-for-like swaps and when they would pass the job to a plumber. Ask how they will turn off and test the water. Ask for the cost in writing, and keep the old part if you want to see what was replaced.
Worth reading first:
Related jobs:
Common questions
Can a handyman fix a dripping tap?
Yes. Fixing a dripping tap is common handyman work. They turn off the water, replace the washer or cartridge, and check that the leak has stopped. If the tap body is worn or corroded, they may suggest replacing it.
Is it a plumber or a handyman job?
A handyman can repair a tap and swap one like for like on existing pipes. A plumber is the right person for extra pipework, moving a tap or any work on the supply lines. Ask the handyman where they stop, and for anything involving gas, use a Gas Safe registered engineer.
How do I stop a tap dripping myself?
Turn off the water at the isolation valve or stopcock, then take the tap apart and replace the washer or cartridge. Our guide on how to fix a dripping tap gives the steps. Take the old part to a shop to match its replacement.
Should I repair or replace a leaking tap?
A repair suits a tap that is in good condition and only needs a washer or cartridge. Replacement is better if the tap keeps dripping after a repair, has a stiff handle, or is corroded. A handyman can tell you which suits your tap.
Can I supply my own tap?
Yes. Many people buy a tap and ask the handyman to fit it, which keeps costs clear. Check that it fits your sink or basin, and that the fixings and connectors are in the box. Ask whether the handyman will supply any missing parts.